Fujian zhichuan mechanical equipment Co., Ltd.
Fujian zhichuan mechanical equipment Co., Ltd.
Add to Cart
Product Description:
Advantages and features of Danfoss cycloidal motors
High-efficiency power output: optimized design, capable of providing efficient power output.
High reliability: reliable quality, suitable for various working conditions.
Multiple model options: models with different displacements and pressures are available to meet different application requirements.
Compact structure: small size, light weight, more flexible and convenient installation and layout.
High efficiency: using toothed stator and rotor pairs, high mechanical efficiency, high-pressure operation and long life.
High load capacity: using double-jointed angular ball bearings, can withstand large radial and axial loads.
Advanced flow distribution mechanism: has the characteristics of high flow distribution accuracy and automatic wear compensation.
Multiple installation forms: provides a variety of flange, output shaft, oil port and other installation and connection forms.
Strong corrosion resistance: using anti-corrosion parts, can withstand challenging harsh conditions.
Low leakage design: with low leakage design, more energy-saving.
Optimized clearance design: advanced cycloidal design and optimized clearance design reduce leakage and ensure the low-speed stability of the product.
High-pressure shaft seal: The high-pressure shaft seal feature enables the product to achieve the best adaptability, reliability and flexibility.
Precautions for the use of Danfoss cycloidal motors
Installation:
The mounting bracket must be sufficiently rigid and the motor must not vibrate.
The output shaft of the motor must be coaxial with the center line of the connected coupling.
When the motor's oil inlet and return oil use steel pipes, the stress on the pipeline must be completely removed to ensure that the pipeline does not exert any force on the motor.
When connecting the drain pipe, the resistance of the return oil should be controlled below 0.3MPa, and the return oil pipe should be connected to the oil tank separately, and must not be connected in series with other return oil pipes.
Before starting the motor, you must first inject enough clean hydraulic oil into the motor housing from the two oil ports, and then rotate the output shaft. If there is no abnormality, you can install it.
The radial load on the motor output shaft must not exceed the specified limit.
System design:
The intermittent working pressure of the motor refers to the maximum working pressure that the motor oil inlet can withstand; while the continuous working pressure refers to the pressure difference between the oil inlet and the oil return port.
The motor cannot be used at maximum speed and maximum pressure at the same time.
Under intermittent working conditions, the motor should not run for more than 10% per minute.
The maximum oil temperature is 80℃.
The shaft seal assembly used in the cycloidal motor can usually withstand higher working pressures. However, in order to ensure good service life and overall mechanical performance, it is recommended that the back pressure does not exceed 5MPa. If the back pressure exceeds this range, it is recommended to connect the external leakage oil pipe.
Before the motor reaches full load, it should be run-in. It is recommended to run-in at less than 30% of the maximum working pressure for 1 hour.
Usage and maintenance:
After the motor has been running for about 200 hours, the oil should be replaced and the oil filter cleaned.
If the oil is too viscous, it may cause cavitation in the oil pump when starting in cold weather, which may damage the oil pump.
When selecting hydraulic oil, all components in the system must be considered and adjusted appropriately to obtain the best viscosity range.
If the color of the oil turns black, it may indicate an overheating problem.
If the oil is emulsified, there may be water contamination.
| Current | 1A |
| Housing Material | Aluminum |
| Ambient Temperature | 0-40°C |
| Mounting Type | Flange |
| Color | Silver |
| Operating Temperature | -10 to 50 degrees Celsius |
| Product Type | Motor |
| Ip Rating | IP65 |
| Stock | Available |
| Cooling | Air-cooled |
FAQ
Q1: Wonder if you accept small orders?
A1: Do not worry. Feel free to contact us .in order to get more orders and give our clients more convener ,we accept small order.
Q2: Can you send products to my country?
A2: Sure, we can. If you do not have your own ship forwarder, we can help you.
Q3: What's your payment terms ?
A3: By T/T,LC AT SIGHT,100% full payment.
Q4: How long is your production lead time?
A4:It depends on product and order qty. Normally, it takes us 15 days for an order with MOQ qty.
Q5: When can I get the quotation ?
A5: We usually quote you within 24 hours after we get your inquiry. If you are very urgent to get the quotation.Please call us or tell us in your mail, so that we could regard your inquiry priority.